Leaking Tank or No Hot Water: What to Do While You Wait
A leak from the tank body is almost never repairable, but a leak from a fitting, valve or drain often is. Turn off the heater's power at the breaker or set the gas control to off, then shut the cold supply valve so the tank stops refilling.
If the floor drain is nearby, let the water run there. If not, a wet vacuum and a few towels buy time. Do not touch wiring or the burner area while it is wet.
Common Water Heater Faults We Repair
No hot water at all
On an electric unit this is often a tripped breaker, a failed upper element or a bad thermostat. On gas it is usually a pilot, thermocouple or gas valve fault.
Lukewarm water
A failed lower element, a stuck dip tube or a thermostat set too low. Sediment can also blanket the burner or element.
Rumbling or popping
Hard water scale on the tank bottom traps steam. Flushing helps, but a heavily scaled tank may be near the end of its life.
Water from the relief valve
A weeping valve can mean high pressure or a worn seat. A valve discharging steadily is a safety issue and needs a plumber the same day.
Rust-colored hot water
Corroded anode rod or tank lining. If only hot water is brown, the tank is likely corroding from inside.
Pilot will not stay lit
A worn thermocouple or a draft. A new thermocouple is a small, inexpensive part when it is caught early.
Repair or Replace: How We Decide
A tank that is under about eight years old with a failed part is usually worth repairing. A tank that is leaking from the body, rusting through or more than ten to twelve years old is better replaced, and our water heater replacement service handles that same visit when it makes sense.
We tell you the cost of both paths before any work starts so the decision is yours.
| Symptom | Likely cause | Typical outcome |
|---|---|---|
| No hot water, electric | Element, thermostat or breaker | Repair |
| No hot water, gas | Pilot, thermocouple, gas valve | Repair |
| Water at base of tank | Fitting leak or tank failure | Repair or replace |
| Rusty hot water only | Corroded tank | Usually replace |
| Rumbling and slow recovery | Sediment on the tank floor | Flush, or replace if heavy |
Need hot water back?
Call and tell us the brand, fuel and what you see. We will tell you the likely fix before we arrive.
What Water Heater Repairs Cost
Small parts such as a thermocouple, element or thermostat sit at the low end of typical US repair ranges, roughly $150 to $450 with labor. Gas valves, tankless control boards and heat exchangers cost more. You get the price before we begin, and these factors set it:
Ask your insurer whether a sudden leak from a failed appliance is covered. Slow leaks and age-related failures often are not.
Hard Water and Chaska Water Heaters
The City of Chaska's 2025 drinking water report lists the city's water as hard, at 26 grains per gallon, and says a water softener is very important for the water's aesthetics. Hard water leaves scale on heating elements and the tank floor, which is why we see element failures and rumbling tanks here.
Flushing the tank once a year slows scale. A water softener reduces it at the source.
Relief valves and discharge pipes are checked against the Uniform Plumbing Code (UPC), which Minnesota's plumbing code is based on, and we do not cap or bypass a safety valve.
Source: City of Chaska 2025 Drinking Water Report.
Water Heater Repair Questions in Chaska
Yes. We answer 24/7 and take after-hours calls for leaking tanks and no-hot-water situations. We cannot promise a fixed arrival time, but we help you make the situation safe while a plumber heads your way.
Water near a gas burner or electric wiring is a hazard. Shut off power or gas control and the cold supply, then call. If you smell gas, leave the house and call 911 and your gas utility before anything else.
Yes. Common faults include error codes, scale in the heat exchanger, failed igniters and flow sensors. Many tankless faults in hard water areas trace back to scale, so we also check the flush history.
Most part swaps take one to two hours once we have the part. If the part is not on the truck we tell you, and we can often restore partial hot water or make the unit safe in the meantime.
Usually a failed lower element on electric tanks, a dip tube problem or heavy sediment taking up tank space. Sizing also matters if household use has grown since the heater was installed.
Chaska requires a plumbing permit for installation, alteration, repair or addition of plumbing, including water heater replacement. Ask the City inspections office at 952-448-9395 whether a specific repair needs one, and we pull the permit for work that does.
